Making Orgonite.

We have looked at the three materials used in tactical orgonite and now we will learn how to combine them in a simple and practical manner. We will be making a Tower Buster (TB) which is a more or less ‘standard’ size (around 5cm diameter and perhaps 3cm thick). 1. TB standard The name ‘Tower Buster’ derives from its primary use which is to convert the negative energy from a single telecommunications tower into positive orgone. First we need to select a suitable mould in which to cast the TB. 2. TB mould I like to use cheap plastic moulds such as may be used to sell individual portions of jelly in at the supermarket. Others prefer to use the multiple trays of cup-cake moulds. One may also use an aluminium soft-drink can cut in half. A glass may also be used. Remember that the resin can become quite hot during the curing process due to the catalytic reaction and may melt some plastics. Resin shrinks slightly when cured and will free itself from most smooth-sided moulds without the need of a release-agent. We will place the dry materials in the mould first and pour the resin in last. When the resin has filled all spaces between the metal and resin; it will form a flat surface just above the metal shavings. Resin without shavings in is not orgonite. Shavings without resin around them is also not orgonite. Only the parts of the TB that form an approximately 50/50 mix of resin and metal shavings (plus crystal, of course) will work as orgonite. We will be combining the materials in the mould with this in mind. First we will put in the crystal pieces as it is more difficult to form a flat surface with them sitting on top of the shavings. 3.Mould + Crystal Then we will put in enough metal shavings to form slightly less than the required thickness of the TB. The shavings should form a flat and level surface. 4. Mould + Crystal + Shavings If your metal shavings contain a proportion of larger pieces that may be difficult to form into a flat surface; place some of these in the mould first and sprinkle some finer shavings on top. The finer shavings will fall into the spaces between the larger pieces of metal and finally form a flat layer to the ingredients in the mould. They will also help to achieve the required 50/50 mix of metal and resin. Next we will pour some resin into a mixing jug; put the required proportion of catalyst in and mix it thoroughly. 5. Resin Jug Catalyst The catalysed resin is then poured onto the mould.



I like to slosh in slightly less than is needed and let it sink through the shavings first; then come back and gently top it up to the right level. If individual moulds are used; any surplus in one TB can be easily poured into another mould that may contain too little resin. If multiple cake-moulds are used; this will not be possible of course.   Finally; any metal shavings that may appear above the surface of the resin can be poked down using your mixing stick. Wait until the resin is thoroughly cured; then turn your TB upside down and free it from the mould by tapping it sharply on the work bench. Dan. Admin BG blog.

8 Responses to “Making Orgonite.”

  1. Legaturi EMF, orgone | Sanatatea si Poluarea Electromagnetica Says:

    [...] Cum sa faci un orgone: [...]

  2. Johanna Chrysanthopoulou Says:

    may i to use green quarz for white?

  3. admin Says:

    Hi Johanna.

    You may use any natural crystal material.
    If a broken surface has a shiny appearance and it is hard enough to scratch glass; it will work well in orgonite.

    All the best.

    BG blog.

  4. Galerija Orgonita - Stranica 178 - Alternativa Forum Says:

    [...] Baš sam našao jednu stranicu pa pogledaj što kažu citiram sa stranice na engleskom: Resin without shavings in is not orgonite. Shavings without resin around them is also not orgonite. [...]

  5. Bulgaria Says:

    Hi mate, you do not seem to use frequencies, or chakras, or mental power during the curing phase of your orgonites. Is that something you just haven’t wrote about, or you don’t do it at all?

  6. admin Says:

    Hi Stefan.

    My primary interest in orgonite construction is a technical one.
    The neutralization of electromagnetic radiation etc by means of the inductor matrix (resin insulated metal spirals) and the electrostriction effect of many crystal materials.

    Whilst I’m aware that others swear by prayer, incantation, intention etc; I have never been particularly interested in this line of endeavour.
    The orgonite that is made in the absence of such programming seems to remove the negative influences on the naturally positive etheric field very well.

    Perhaps you would like to write a post for us on the topic you describe.

    All the best.

    Admin. BC blog.

  7. Bulgaria Says:

    Nope, I am a technical guy, just like you :) I wanted to confim, for my reasearch, that you do not use the ‘other’ things, cause ppl like us are rare in this domain ;)

  8. Don Blizard Says:

    Greetings to all.

    I’m also a techie as well as relative newbie wanting to know the best ingredients for use in countering the negative effects of EMF.

    So far, I’ve accumulated some Brass shavings, as well as assorted metal key shavings, as well as quartz crystals, and Iron & Shungite in powdered form.

    Would these combined materials with a fiberglass resin at the recommended 50/50 ratio be adequate for the task of remediating the negative effects of EMF?

    And would this be effective toward gifting towers and power stations nearby as a tower buster?

    Also wondering if there is anything else I would need to add to increase the etheric energy output?

    Thanks so much in advance.

Leave a Reply